
Installation and Use
H1 / H1+ user manual
Mechanical installation:
You most likely need to move your mirror-clutch assembly just few millimeters to get the needed space (9 mm) for SilverFox clamp arm.​​
​
Slide the plastic adjustment ring on to the 22 mm handlebar. By rotating the adjustment ring you can move the controller forward or backward on the motorcycle handle bar. Clamp the device on the adjustment ring evenly with two M4 screws.
Asennus:
Tee tilaa kontrollerin kiinnitinvarrelle siirtämällä peili-kytkin-kokoonpanoa 9 mm oikealle.
​​
Asenna muovinen säätörulla 22 mm ohjaustankoon. (saatavilla myös 25 mm halkaisijalla). Pyörittämällä säätörullaa voit hienosäätää kontrollerin asentoa eteen- tai taaksepäin. Kiristä laite sopivaan asentoon kiristämällä tasaisesti kumpaakin M4 ruuvia.
​Connect the power cord to the fuse protected 12VDC output (post ignition) of your bike (Operating voltage range 5-24VDC). Double check to make sure to connect the cords are correct; Brown wire to negative (-) and White wire to positive (+).
​​​​​
H1 (from 5/2024) units are supplied with M12 connectors to plug&play with DMD T865 harness. And with extra cable strip for just 12VDC power feed for other systems. ​
Yhdistä virtajohto sulakkeella varmistettuun (virta-avaimella kytkeytyvään) 12VDC ulostuloon. Käyttö jännite laitteelle on 5-24VDC. Varmista RUSKEA johto on miinus (-) ja VALKOINEN on plus (+)
​​​​
H1 laitteet on varustettu M12 liittimellä, joka sopii Plug&Play DMD T865 laitteiden johtosarjaan. Tukee DMD:n cable connection - yhteyttä ja saa 12VDC syötön liittimen kautta.
​
Ylimääräinen kaapeli voidaan kytkeä 12VDC ulostuloon, jos käytössä ei ole T865 tablettia.

​Connect bluetooth:
Power on the SilverFox navigation controller. Open the Bluetooth settings on your Android device. Find and tap on the device e.g. "SilverFoxH1" from the list of devices. Accept the pairing request. Your SilverFox navigation controller is now paired using Bluetooth.
​
For T865(x) users SilverFox prefer Bluetooth connection. C1 support DMD cable connection communication system, but then you are limited to use your controller in F1 mode only (more of this in Keyset-section below).
​
Yhdistä bluetooth:
​Käynnistä C1 kontrolleri. Avaa Bluetooth asetukset Android laitteessasi. Valitse "SilverFoxC1 bluetooth listasta. Hyväksy paritus. Nyt laite on Bluetooth-yhdistetty.
​​
T865(x) käyttäjille SilverFox suosittelee käyttämään Bluetooth liitosta. C1 tukee myös DMD:n kaapeliyhteyttä, mutta silloin voit käyttää vain F1 -tilaa (lisää aiheesta Keyset-osiossa edellä).
Installing the Button app:
If you use DMD T865 or T865X tablet, you can skip this section. The Button App is preinstalled on your system allready. SilverFox prefer Bluetooth connection mode, you have to go to The Buttons App and disable cable connection option in "remote" setup.
​​
Please note:
You don't need to install the Buttons app if you don't use other F1 apps than DMD2. Please check the list of F1 apps here.
Download Button app , unzip it and install it to your Android device. On first run the app will ask to enable the the accessibility service for Button app. Follow the link and allow the service and permission to use the app.
Please check the video. Demo done with Samsung Activetab 3, Android 13 OS.
​
Asenna the Button app:
Jos käytätä DMD T865 (x) tablettia, voit skipata tämän osion. The Button App on esiasennettu laitteeseen jo tehtaalla. SilverFox suosittelee käyttämään Bluetoot yhteyttä, joten mene Buttons:in "Remote" asetuksiin ja "Disable" cable connection valinta.
​​
Huomioitavaa:
Buttons appia ei tarvitse asentaa jos et käytä muita kuin DMD2 ohjelmaa F1 tilassa. Katso lista F1 ohjelmista tästä.
​
Lataa Button app , pura se ja asenna Android laitteeseen. Kun avaat ohjelman ensimmäistä kertaa, ohjelma pyytää hyväksymään "accessibility service" Button appille. Seuraa linkkiä ja hyväksy luvat käyttääksesi ohjelmaa.
​
Katso video. Demo on tehty käyttäen Samsung Activetab 3, Android 13 käyttöjärjestelmässä.
​
Center
Zoom out
Zoom in

Panning Joystick
​Operating the HomeOne:
​
The Keysets:
​
The controllers has two selectable keysets. Both keysets are pre-programmed to send different key codes to the Android device. For example zoom in -button send different command in F1 set than in F2 mode. HomeOne device remember the keyset state when you power off the unit.
​​​
In HomeOne and HomeOne+ controller press both Zoom buttons shortly at the same time, toggles between F1 and F2 ​
​
F1-keyset:
Choose for map applications such as DMD2, OsmAnd, LocusMaps, Google Maps, Waze, Gaia GPS, etc. (listed in Button app).
​
Joystick movements corresponding left, right, up and down
​
+ and - buttons are zoom in and out
​
centering/orientation button center the map to your current position.
​
F2-keyset:
Choose for apps that has special key mappings like MyRoute, Stegra.io, Kurviger, Mapitare, Ranniot, Tracker, Locus Maps or Osmand
.
Joystick movements corresponding left, right, up, and down
​
Center => letter 'C'
​
Center hold => letter 'D'
​
+ => character '='
​
Hold + => letter 'A'
​
- => character '-'
​
Hold - => letter 'B'
HomeOne (H1 ja H1+) käyttö:
​
H1(+) kontrollerissa on kaksi valittavaa key-settiä, F1 ja F2. Kummatkin on esi-ohjelmoitu. Tilat lähettää eri komentoja Android laitteeseen. Esimerkiksi "zoom in" lähettää F1-tilassa eri komennon kuin F2 tilassa. Laite muistaa viimeisimmän asetuksen kun katkaiset virrat laitteesta.
​​
Vaihtaaksesi F-tilan H1 tai H1+ kontrollerissa, paina kumpaakin zoom näppäintä lyhyesti yhtäaikaa. H1+ LED valot näyttävät aktiivisen F-tilan.
​​
F1-tila:
Käytä tätä tilaa karttasovelluksissa kuten DMD2, Google Maps, Waze, Gaia GPS, jne. (Button appsin alaisia ohjelmia. Lista löytyy ohjelmasta) .
​
Joystick liikkeet ovat vasen, oikea, ylös ja alas.
​
+ ja - näppäimet ovat zoom in ja out
​
Keskitys näppäin keskittää kartan.
​
F2-keyset:
Käytä F2 tilaa ohjelmiin kuten MyRoute, Stegra.io, Kurviger, Mapitare, Ranniot, Tracker, Locus Maps or Osmand...
​
Joystick liikkeet ovat vasen, oikea, ylös ja alas.
​
Center => kirjain 'C'
​
Center pito => kirjain'D'
​
+ => merkki '='
​
pito + => kirjain 'A'
​
- => merkki '-'
​
pito - => kirjain 'B'